基層處理：清理電梯門洞口周邊的雜物、灰塵，確?；鶎悠秸⒏稍?。若洞口存在不平整或缺陷，需進行修復，如用水泥砂漿填補孔洞、用砂紙打磨突出部位，為后續安裝提供良好基礎。?

Grassroots treatment: Clean up debris and dust around the elevator door opening to ensure a smooth and dry base. If there are unevenness or defects in the opening, repair should be carried out, such as filling the hole with cement mortar or sanding the protruding part with sandpaper, to provide a good foundation for subsequent installation. ?

安裝包口框架：將預先加工好的不銹鋼包口框架，通過不銹鋼螺絲或角碼固定在電梯門洞口上。安裝過程中要使用水平儀、鉛垂線等工具，確?？蚣艿乃蕉群痛怪倍?，誤差控制在 ±1mm 以內?？蚣馨惭b牢固后，檢查其與洞口的貼合度，如有縫隙，用密封膠填充密封。?

Installation of package frame: Fix the pre processed stainless steel package frame onto the elevator door opening with stainless steel screws or corner brackets. During the installation process, tools such as level gauges and plumb lines should be used to ensure the levelness and verticality of the frame, with an error controlled within ± 1mm. After the frame is firmly installed, check its fit with the opening. If there are gaps, fill and seal them with sealant. ?

安裝面板：將經過表面處理的不銹鋼面板安裝在框架上，可采用粘貼、卡槽固定等方式。粘貼時，選用優質的結構膠，均勻涂抹在面板背面，確保粘貼牢固；卡槽固定則需提前在框架和面板上加工好對應的卡槽，安裝時將面板準確嵌入卡槽內，輕輕敲打使其緊密結合。安裝完成后，檢查面板的平整度和拼接縫隙，縫隙寬度應均勻一致，一般不超過 0.5mm，若有縫隙過大或不平整的情況，及時調整。?

Installation panel: Install the surface treated stainless steel panel onto the frame using methods such as pasting or slot fixing. When pasting, use high-quality structural adhesive and evenly apply it to the back of the panel to ensure a firm adhesion; To fix the card slot, it is necessary to process the corresponding card slot on the frame and panel in advance. When installing, accurately insert the panel into the card slot and gently tap it to make it tightly fit. After installation, check the flatness and splicing gaps of the panel. The gap width should be uniform and consistent, generally not exceeding 0.5mm. If there are gaps that are too large or uneven, adjust them in a timely manner. ?

收口處理：對不銹鋼包口的邊緣、轉角等部位進行收口處理，用密封膠填充縫隙，使邊緣整齊、美觀，同時增強防水、防塵性能。在電梯門與包口的交接處，安裝橡膠密封條，減少關門時的碰撞噪音，提高密封性。

Sealing treatment: The edges, corners, and other parts of the stainless steel package are sealed with sealant to make the edges neat and beautiful, while enhancing waterproof and dustproof performance. Install rubber sealing strips at the junction of elevator doors and package openings to reduce collision noise during door closing and improve sealing performance.

本文由安徽不銹鋼包口友情奉獻.更多有關的知識請點擊:http://www.yqzzdz.com.cn我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

This article is dedicated to friendship For more information, please click: We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message